G2 Supersand Bond
G2 Supersand Bond

Gator Maxx G2

FOR PAVER AND NATURAL STONE JOINTS UP TO 4”
FOR OVERLAY & NON-OVERLAY APPLICATION

NO DUST • HAZE FREE • NO BLOWER • ONE WATERING

Description

(FOR RESIDENTIAL AND COMMERCIAL APPLICATIONS)

GATOR MAXX G2 is made with a state-of-the-art manufacturing process. Specifically, calibrated sand is mixed with sophisticated intelligent polymers. This new generation of Intelligent Polymers neutralizes haze and dust. The polymeric sand application is now dust free and haze free. No blower is needed and the intelligent polymeric sand requires only one watering. GATOR MAXX G2 is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. Available in Beige, Slate Grey, Ivory and Black Diamond.

Features

  • Can be used on false joint pavers.
  • For overlay, non-overlay, residential and commercial applications.
  • Can be used for joints up to a maximum of 4 inches.
  • Helps prevent weeds and damage caused by burrowing insects.
  • Helps prevent erosion due to wind, rain and freeze/thaw cycles.
  • For NON-OVERLAY, G2 sets within 1 hour after water activation at above 32°F, (no rain within 1 hour after water activation)
  • For OVERLAY, G2 sets within 1 hour after water activation at above 32°F (no rain within 24 hours after water activation)
  • No Dust, Haze Free, No Blower, and one watering.
  • Intact pallets can be stored outside.
  • Ideal for Gator Base applications.

Clay Pavers

If used on clay pavers make sure they are 100% dry. Clay pavers tend to hold moisture, which can prematurely activate the GATOR MAXX G2 while the sand is being spread over the paver surface, leaving a residue. Always apply on a test area before using the GATOR MAXX G2 on clay pavers.

Moss

GATOR MAXX G2 will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on-site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product.

Coverage

Quantity required depends on the shape and size of the concrete pavers as well as the width of the joints.

Narrow Joints Wide Joints
sq. m. sq. ft. sq. m. sq. ft.
Beige, Slate Grey, Ivory
50 lbs / 22.7 kg
6.00-7.41 65-85 2.00-3.88 22-42
Black Diamond
50 lbs / 22.7 kg
5.50-6.5 58-76 1.8-3.5 20-38

Helps Prevent

no weeds>
Helps prevent weed sprouting.
no ants
Helps prevent damages caused by insects.
anti errosion
Helps prevent erosion due to climatic conditions, such as wind, rain and freezing temperatures.

4 BEAUTIFUL COLORS TO CHOOSE FROM

Gator Color Pallet

CLICK HERE TO SEE YOUR FAVOURITE COLOR WITH YOUR PAVER CHOICE

CLICK HERE TO SEE YOUR FAVOURITE COLOR WITH YOUR PAVER CHOICE

FOR USE ON AND REQUIRED SUB-SURFACE PREPARATION

GATOR MAXX G2 is recommended for a variety of uses including pool decks, patios, footpaths, driveways, parking spaces, pavements, etc. The concrete pavers must be installed on a drainage base system composed of 2 layers. The upper layer can have a maximum of 1 inch of bedding sand. The lower layer must have a minimum of 6 inches of crushed stone compacted at 98 % Proctor density. (See diagrams).

FOR OVERLAY APPLICATIONS

  • Remove all loose and fragile concrete.
  • Cover the ground with a geotextile, refill with crushed stone and compact it.

GATOR MAXX G2 INSTALLATION STEPS (FOR A NEW PAVER SURFACE)

Installation Step 1

Step 1

Step 1

Spread GATOR MAXX G2 with hard-bristle broom. Make sure the GATOR MAXX G2 completely fills the joints. Do not use other materials in the joints. Leave a layer of GATOR MAXX G2 on the surface to aid in the vibrating and consolidation of GATOR MAXX G2 into joints.

Installation Step 2

Step 2

Step 2

Vibrate the GATOR MAXX G2 into the paver joints using a vibratory plate compactor. A rubber pad is recommended. A roller compactor is best for slab installation.

Joints should be filled up to 1/8 inch below the edge or chamfer. It is best to compact in several directions to ensure there are no air gaps or voids in the joints. Repeat steps 1 and 2 to ensure joints are filled and consolidated. Narrow joints require more care to completely fill.

Installation Step 3

Step 3

Step 3

Sweep off excess GATOR MAXX G2 from the paved surface, first with a hard-bristle broom, then a soft-bristle broom. Take care to leave the height of the polymeric sand at least 1/8 inch below the edge or chamfer of the paver.

Installation Step 4

Step 4

Step 4

Activate GATOR MAXX G2 by showering 50 sq. ft. section for 1 minute, starting at the lowest point. Once all the sections are activated, rinse off any debris that is on the total paver surface.

IMPORTANT INSTALLATION NOTES FOR G2

  • A Pavers and slabs must be installed according to ICPI Tech Spec #2 non-overlay (www.icpi.org) before GATOR MAXX G2 installation. For Overlays ICPI recommends 2 inches diameter drainage holes spaced approximately 10 feet apart and at the lowest elevations in the slab. Holes should be filled with #8 stone and covered with a 1 foot x 1 foot patch of geotextile. Drilled holes should allow any water entering the bedding layer to freely flow out.
  • B Always refer to the latest GATOR MAXX G2 Technical Data Sheet at AllianceGator.com before installing GATOR MAXX G2.
  • C Pavers’ sides and top surfaces must be completely dry. Do not apply if the paver surface is damp or wet. The damp or wet surface will cause GATOR MAXX G2 to prematurely activate and will lead to the polymers sticking on the paver surface.
  • D Do not apply if the paver joints are damp or wet. This will prevent the GATOR MAXX G2 from properly sliding into the joints and obtaining very densely packed joints, which is critical to the product’s performance.
  • E Temperature must be above 32°F with dry conditions and a minimum of 1 hour of dry weather required after activation (for overlays, 24 hours).
  • F Avoid excessive watering or flooding of paver surface.
  • G For all paver surfaces, and particularly around in-ground pools, there must be a slope of 1/8 inch per linear foot away from the edge of the pool or structures to ensure optimal performance of the GATOR MAXX G2.
  • H For the pool coping units, it is mandatory to use mortar in the joints. For the rest of the paver installation around the pool, you can use GATOR MAXX G2.
  • I Do not sweep GATOR MAXX G2 over asphalt.
  • J Install GATOR MAXX G2 a minimum of 1/8 inch below the paver surface or erosion may occur. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tires. Joints should be filled up to 1/8 inch below the edge or chamfer.

IMPORTANT WATER ACTIVATION NOTES FOR G2

  • A Work in manageable sections, ideally about 50 sq. ft. at a time, depending on temperature.
  • B Do not allow GATOR MAXX G2 to wash out of joint.
  • C Never allow paved surface to dry out during the water-activation phase.
  • D Watering must be started at the lowest point of the paved surface.
  • E Use a watering gun connected to a hose. Set to shower.

GATOR MAXX G2 INSTALLATION (FOR AN EXISTING PAVER SURFACE)

When using GATOR MAXX G2 to replace existing jointing materials, old jointing materials need to be completely cleaned out of the joints and pavers completely dry before installing GATOR MAXX G2. Be careful not to disturb the bedding material under the pavers. Follow steps 1 to 4 of GATOR MAXX G2 installation steps for a new paver surface.

15 year limited warranty

Please note that this limited warranty applies when the product is used for residential purposes exclusively (home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential use). The manufacturer cannot guarantee results as it has no control over surface and sub-surface preparation and product application. (Proper installation of pavers or slabs to ensure long-term stability of work, including granular foundation of certified crushed stone of 0-3/4 inch (0-20 mm) bedding layer and appropriate installation of borders in accordance with above specified method for applying product). However, for a period of 15 years from purchase, the manufacturer agrees to refund the purchase price if the product is proven to be defective and on the condition that it was installed pursuant to the method of application of surface and sub-surface preparation described above. Proof of purchase is required for any claim.

Exclusion of responsibility

THE PARTIES AGREE THAT REFUND OF THE PURCHASE PRICE AS STATED IS THE ONLY OBLIGATION OF THE MANUFACTURER. IN ALL EVENTS, THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES OR COSTS WHATSOEVER, (INCLUDING REMOVAL OR REINSTALLATION OF SAND OR PAVERS) DIRECT OR CONSEQUENTIAL. TO THE EXTENT PERMITTED BY LAW, THE MANUFACTURER EXCLUDES ANY IMPLIED WARRANTY OF QUALITY, MERCHANTABILITY OR FITNESS FOR PURPOSE. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for the presence of moss, mold, mildew, or similar factors that may occur on the product after its installation. ALLIANCE DESIGNER PRODUCTS INC. excludes any responsibility for use of SUPERSAND BOND G2 with Clay Pavers or any installation not installed to manufacturer’s specifications and ICPI Tech Spec #2.

* ICPI Tech Spec #2

1 year limited warranty (commercial)

Please note that when the product is used for other purposes (Mixed-use, commercial, institutional or other), the above terms apply except that the applicable period is reduced to 1 year from purchase.

Warranty Logo