Gator Dust Bond is a unique mixture of polymer binders and calibrated stone available in Sahara Beige, Stone Grey. Once Gator Dust Bond sets, it becomes very firm and locks between the wet cast or natural stone joints while still retaining flexibility and providing a long lasting, durable jointing material. Gator Dust Bond is recommended for a variety of uses including pool decks, patios, footpaths, and any other pedestrian applications.
Install the stones on a maximum 1″ (2.5cm) bedding of sand. Make sure that there is at least 6″ (15cm) of compacted crushed stone under the bedding sand. See diagram 1.
Make sure the wet cast or natural stone’s top surfaces are dry.
FOR NATURAL STONES: Using a hard-bristle, broom, sweep Gator Dust in between the full depth of the natural stone joints.
FOR WETCAST STONES: Using a scoop, carefully pour Gator Dust in between the full depth of the joints and avoid getting any Gator Dust on the wet cast stone surface.
Hit the wet cast or natural stones with a rubber mallet; this will make the Gator Dust settle firmly into the joints by removing any air pockets. Repeat step 2 and this step 3 at least two more times.
Using a soft, fine-bristle broom, sweep all excess Gator Dust off stone surfaces. Ensure that Gator Dust lies at least 1/8 inch (3 mm) below the top wet cast or natural stones surfaces.
Using a leaf blower, blow all Gator Dust residues off wet cast or natural stone surfaces.
Shower a specific 50 sq. ft. (4.5 sq. m.) area for 90 seconds.
Continue to do the rest of the area at 50 sq. ft. (4.5 sq. m.) area for 90 seconds.
When the entire surface is done, rinse off any GATOR DUST residue off the surface.
Use a leaf blower to remove any excess water remaining on the wet cast or natural stones pores and crevices. This blowing action is necessary to help remove any remaining Gator Dust residue left on wet cast or natural stones surfaces from the previous steps.
IMPORTANT: The water used in step 6 will activate a bonding action as well as condensing GATOR DUST in the joints. Too much water will undo the dense compaction obtained during step 3 and reduce the final performance of GATOR DUST.
PLEASE NOTE: GATOR DUST becomes very firm but will detach from wet cast or natural stones if the crushed stone base has excessive movement. It will also detach from the wet cast or natural stones if the wet cast or natural stones are oscillating back and forth due to improper installation. By following GATOR DUST installation instructions carefully, you will obtain a very hard jointing material. It should be noted that GATOR DUST will continue to harden over time. Avoid excessive watering or flooding of wet cast or natural stone areas. When installing wet cast or natural stones around an underground pool, a slope of 1/8 inch (3 mm) per linear foot away from the pool is mandatory. All wet cast or natural stone surfaces must have a drainage slope for the GATOR DUST to work at its optimum. For the pool coping blocks, it is mandatory to use mortar in the joints. For the rest of the wet cast or natural stones installation around the pool, you can use GATOR DUST. Do not sweep GATOR DUST over asphalt.
The quantity required depends on the shape and size of the wet cast or natural stones as well as the width of the joints. One bag of 50 lb (22.7 kg) of this product will cover between 20 to 30 square feet (1.9 to 2.8 m2) if the joints are about 1˝ to 2˝ (25 mm to 5 cm) wide and the stones are about 2˝ to 2-1/2˝ (5 cm to 6.4 cm) thick.
|Products||Retail Size||Units per Pallet|
|Gator Dust Bond – Sahara Beige||22.7 kg (50 lb)||56|
|Gator Dust Bond – Stone Grey||22.7 kg (50 lb)||56|
Gator Dust is recommended for a variety of uses, including patios, walkways and pool decks. The wet cast or natural stones must be installed on a traditional base system: maximum of 1˝ (2.5 cm) of bedding sand, plus a minimum of 6˝ (15 cm) of crushed stone compacted at 98% Proctor density. (See diagram on left.)
Please note that this limited warranty applies only when the product is used for residential purposes exclusively. (Home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential use.) The manufacturer cannot guarantee results, as it has no control over surface and sub-surface preparation and product application. (Proper installation of natural or wetcast stones to ensure long-term stability of work, including granular foundation of certified crushed stone of 0-20 mm bedding layer and appropriate installation of borders in accordance with above specified method for applying product.) Also warranted when used with Gator Base. However, for a period of 15 years from purchase, the manufacturer agrees that, if the product is proven to be defective, and on the condition that it was installed pursuant to the method of application of surface and sub-surface preparation described above, then the manufacturer agrees to refund the purchase price. Proof of purchase is required for any claim.
THE PARTIES AGREE THAT REFUND OF THE PURCHASE PRICE AS STATED IS THE ONLY OBLIGATION OF THE MANUFACTURER. IN ALL EVENTS, THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES OR COSTS (INCLUDING REMOVAL OR REINSTALLATION OF SAND OR STONES) WHATSOEVER, DIRECT OR CONSEQUENTIAL. TO THE EXTENT PERMITTED BY LAW, THE MANUFACTURER EXCLUDES ANY IMPLIED WARRANTY OF QUALITY, MERCHANTABILITY OR FITNESS FOR PURPOSE.
Alliance Designer Products inc. excludes any responsibility whatsoever for the presence of moss, mold, mildew, or similar factors that may occur on the product after its installation. The presence of moss, mold or mildew is caused by the particular on-site conditions, including excess moisture shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product after installation.